-
$40.00
This is an unusual neutral density filter on a wafer-thin glass substrate. The optical density is marked on the surface of the filter (0.96) in blue ink. I have not attempted to remove the marking. The filter is very uniform in density (the gradation visible in the photo is an artifact of the lighting). There are a few fine scratches in the coating near the edge with the marking. There is also a fine scratch in the glass on the side opposite the coating (see second photo). It extends most of the way across the filter.
Diameter � 2.000 inches
Thickness � 0.029 inches (0.75mm)
Optical Density � 0.96
.
***MPN
***OEM
***SKU*** 30194
-
$50.00
This is one of a pair of collimation mirrors removed from a 50cm Jarrell-Ash monochromator. The mirrors have the following characteristics.
Size � 84.15mm x 68.07mm
Thickness (at corners) � 17.5mm
Focal length � approximately 515mm
Coating � Al
The mirrors coatings are in rough shape. These will need to be recoated before they are useful. Substrate appears to be undamaged (one of the two mirrors has a very small corner chip that does not impinge upon the coated area). This listing is for a single mirror.
Photo set 1997
***MPN
***OEM Jarrell Ash
***SKU*** 30190
-
$450.00
This concave mirror was removed from an ITEK lens assembly which would speak exceptionally highly of its quality. (ITEK used to fabricate the optics used in the spy satellites for the military and the NSA). Characteristics include:
Diameter � 4.750 inches
Active area � 4.20 inches
Radius � approximately 280mm, CC
Substrate � Zerodur
Coating � Al ?
Weight � 1.30 pounds
The mirror has numerous small pits clustered near the center and a few scattered about the rest of the surface. The rest of the coating and surface appears to be unblemished � no haze and no scratches. The mirror is certainly very serviceable as it sits.
Photo set 1994
***MPN
***OEM ITEK
***SKU*** 30187
-
$600.00
This is a nearly plane concave mirror of 5.5 inches in diameter. The substrate is opaque but relatively light. Characteristics include:
Diameter � 5.50 inches
Figure � concave, R = 8097.4mm
Active area � 5.00 inches
Thickness � 1.017 inches
Substrate –
Weight � 1.99 pounds
The coated surface does have some burns in places � obviously intended for use with a CO2 laser. Otherwise the surface is in excellent condition with a few very light scratchs. The reverse side is marked with the work order number (12281-8A), the part number (7R018069), and the run number (871022-72). Also noted is the radius stated above.
Photo set 1993
***MPN 7R028069
***OEM Custom
***SKU*** 30186
-
$150.00
This grating is ruled on a copper substrate and obviously intended for work with IR lasers.
There was no documentation with the grating other than what was written on the protective capsule..
Ruled area � 28mm square..
Substrate size � 30mm x 30mm
Substrate thickness � 10mm
Coating � appears to be gold with protective coat
Condition of the grating is unknown. There does seem to be some some mottling in the protective coating, and a at certain angles a slight Moire target pattern is visible (possibly from heat). Capsule notes stage 6 micron master, copper, from folded laser. 3M. Dated 20 November 1975.
Photo set 1959.
***MPN 1165-9-5-1
***OEM Brand Unmarked
***SKU*** 30163
-
$110.00
This item is a new Newport 20D20ER.2 Broadband Metallic Mirror.
From Manufacturer Website: The 20D20ER.2 Broadband Metallic Mirror is an excellent general purpose, broadband reflector. This 2 inch (50.8 mm) diameter mirror is made from a 12.7 mm thick Pyrex substrate. Pyrex has low thermal expansion and is an excellent substrate for most applications. The ER.2 protected silver coating is composed of a low emissivity silver film fully encapsulated by a multilayer dielectric stack to prevent oxidation. This coating has excellent broadband reflectivity in the IR, while maintaining very good performance in the visible and near IR. Average reflectivity is greater than 96% from 480�1100 nm and greater than 98.5% from 1.1�20 um. This mirror has a 1/10 wave surface flatness and a 15-5 surface quality.
***MPN 20D20ER.2
***OEM Newport Research Corp (NRC)
***SKU*** 31733
-
$110.00
This item is a new up-opened Newport 13E20BD.1 Broadband Dielectric Eliptical Mirror.
From Manufacturer Website: The 13E20BD.1 Broadband Dielectric Elliptical Mirror is an extremely versatile mirror for laboratory applications and highly efficient over a broad wavelength range. This 1.30 inch (33.02 mm) minor axis, 1.838 inch (46.70 mm) major axis, eliptical mirror is made from a 9.37 mm thick Pyrex substrate. Pyrex has low thermal expansion and is an excellent substrate for most applications. The BD.1 coating reflects all visible laser lines in the range 488�694 nm with greater than 99% efficiency for any polarization at 0�45 degree angle of incidence. And high reflectivity is extended to greater than 98% at 441.6 nm. The BD-1 coating is extremely durable and will withstand repeated cleaning. This mirror has a wave/10 surface flatness and a 15-5 surface quality.
***MPN 13E20BD.1
***OEM Newport Research Corp (NRC)
***SKU*** 31670
-
$80.00
This Newport 900PH-10 High Energy Pinhole Aperture comes from a working environment but has not been tested.
From manufacturer website: The 900PH-10 High Energy Pinhole Aperture is fabricated from ultra-thin molybdenum, a refractory alloy with high heat conductivity and melting point. This material exhibits almost no warping due to localized heating by the laser. A smooth 10 � 1 �m diameter hole with extremely low ellipticity is produced using laser drilling techniques. These pinholes have a laser damage threshold of 75 MW/cm2 CW and are suitable for pulsed laser use up to 700 mJ/cm2. This version is mounted for use with our Model 900 spatial filter.
– Aperture Diameter: 10 +/- 1 um.
***MPN 900PH-10
***OEM Newport Research Corp (NRC)
***SKU*** 30310
-
$500.00
Unit is a Newport 10RP32-532 zero-order precision wave plate.
Specifications:
-Diameter 25.4mm
-Wavelength: 532nm
-Thickness: 6.35mm..
Manufactures description:
The 10RP32-532 True Zero-Order Wave Plate consists of a birefringent polymer film cemented between two high-precision, high efficiency, broadband antireflection coated BK 7 windows. This construction ensures excellent transmitted 532 nm wavefront quality and /2 retardation, while minimizing beam deviation and surface reflection losses. The assembly is mounted in a 25.4 mm outer diameter black anodized aluminum housing for protection and ease of mounting and has a 17.8 mm clear aperture. The wave plate fast axis marked for alignment reference. Polymer wave plates offer benefits over quartz wave plates such as better angular acceptance and less sensitivity to wavelength change. Polymer wave plates have excellent angular field of view. Retardation changes by less than 1% over a �12� incidence angle. The polymer material has very low birefringence that is nearly constant with wavelength..
***MPN 10RP32 -532
***OEM Newport Research Corp (NRC)
***SKU*** 28354
-
$70.00
This item is a used Newport 900PH-15 Hi-energy Pinhole Aperture mounted for Model 900 Filter. The pinhole comes from a working environment but has not been tested.
From the manufacturer website: The 900PH-15 High Energy Pinhole Aperture is fabricated from ultra-thin molybdenum, a refractory alloy with high heat conductivity and melting point. This material exhibits almost no warping due to localized heating by the laser. A smooth 15 � 1.5 �m diameter hole with extremely low ellipticity is produced using laser drilling techniques. These pinholes have a laser damage threshold of 75 MW/cm2 CW and are suitable for pulsed laser use up to 700 mJ/cm2. This version is mounted for use with our Model 900 spatial filter.
Manufacturer Specifications:
– Diameter: 9.525 mm
– Diameter Tolerance: 0.125 mm
– Aperture Diameter: 15 +/-1.5 �m
– Thickness: 15.24 um
– Materia: Molybdenum
– Damage Threshold: 75 MW/cm2 CW, 700 mJ/cm2 with 10 nsec pulses.
***MPN 900PH-15
***OEM Newport Research Corp (NRC)
***SKU*** 30282
-
$269.00
Item is a Newport Research Corp. (NRC) 2″ silver coated Pyrex mirror.
Specifications:
-2″ diameter, 0.49″ thickness
-0.45-12 um
-Pyrex
-Wavelength range 450 to 12000 nm
-Clear aperture >80% of diameter
Manufacture description:
The 5123 General Purpose Silver Coated Mirror can be used over a broad spectral range with better than 95% reflectivity from 450 nm to beyond 12 �m. It’s proprietary silver-based coating makes this 2.0 inch (50.8 mm) diameter mirror highly reflective from 0� to 45� and virtually insensitive to polarization. Protective dielectric coatings make it resistant to tarnish and oxidation. Plus it has minimal phase distortion, so it is useful for ultrafast-pulsed applications with Ti:Sapphire and other lasers.
VIS-IR Bandpass Blocking Filter is an optional blocking filter to shape the spectral output of our 300 to 450 W UV Flood Sources (Simulators). 290 to 400 nm plus residual 650 to 800 nm typical spectral output when used with the 81017 atmospheric attenuation filter. Warning, the 87066 will break if used with lamp power greater than 450 W.
***MPN New Focus 5123 VIS – IR
***OEM Newport Research Corp (NRC)
***SKU*** 28340
-
$120.00
This is a nice selection of seven crown glass singlets of various focal lengths in a special case. The lenses are uncoated and include the following Oriel part numbers:
4020 � 0.5 inch diameter, 13mm focal length
4022 � 0.5 inch diameter, 25mm focal length
4023 � 0.5 inch diameter, 38mm focal length
4024 � 0.5 inch diameter, 50mm focal length
4025 � 0.5 inch diameter, 75mm focal length
5-2425-150 � 1 inch diameter, 150mm focal length
Unknown part number � 1 inch diameter, 35mm focal length
The lenses are all unmounted. Each comes with a protective cloth holder.
Photo set 1791
***MPN 402x Series
***OEM Oriel Corp
***SKU*** 30001
-
$50.00
This is a plane mirror of 25mm diameter and 6mm thickness. The back of the mirror carries a label with the part number BD 103 079 05 � VIS. The mirror appears to have an aluminum coating and is not transmissive. Condition is near-perfect.
Photo set 1786
***MPN BD 103 079 05
***OEM Balzers
***SKU*** 23196
-
$90.00
This is a Dichroic Mirror 2 Inch Diameter with a Frosted Back.
This is a plane glass mirror with a dichroic coating. Specifications include:
Diameter = 2.000 inches
Thickness = 0.501 inches
Polished on dichroic side, obverse is frosted
Axially transmitted color is violet. Condition is excellent � no visible flaws.
Photo set 1785
BMI Surplus, Inc. has a huge inventory of used, new, pre-owned,
recycled, refurbished & used Optical Mirrors for sale.
Buy online or give us a call at 781-871-8868.We have experienced customer
service representatives standing by ready to help you!!
**Shipping, Handling & Freight fees are dependent on your location.
We will provide a freight quote to meet your individual needs and work with you
if you prefer to use your own carrier..
We have over 33 years of experience shipping sensitive scientific instruments & industrial equipment!
Don’t see what you are looking for? Use our orange search box on the top right hand corner of this page to customize your search..
***MPN
***OEM
***SKU*** 23195
-
$99.00
Newport 900PH-1 1.0 Micron
It is easiest to quote the Newport website for specifications regarding this mounted pinhole:
�The 900PH-1 High Energy Pinhole Aperture is fabricated from ultra-thin molybdenum, a refractory alloy with high heat conductivity and melting point. This material exhibits almost no warping due to localized heating by the laser. A smooth 1 +/- 0.5 micron diameter hole with extremely low ellipticity is produced using laser drilling techniques. These pinholes have a laser damage threshold of 75 MW/cm2 CW and are suitable for pulsed laser use up to 700 mj/cm2.�
This pinhole comes mounted into a square steel housing with pin and is intended for use in the Newport Model 900 spatial filter.
The mount of the pinhole states 10 microns, but either the decimal is missing or a 1 micron pinhole has been substituted for the original foil. The pinhole is perfectly round but is only visible with a fairly high magnification microscope.
***MPN 900PH-1
***OEM Newport Research Corp (NRC)
***SKU*** 23191
-
$175.00
Mounted 2X Anamorphic Prism Pair, 780 – 1550 nm
This anamorphic prism pair in a cylindrical mount is used to magnify a laser beam diameter in only one axis by a factor of 2x. Although not marked on the barrel, this was determined to be the prism pair used for the wavelength range of 780 to 1550nm by measuring the beam offset of the mount which was 5.7mm. (The only other 2x prism pair offered by Melles Griot has a 5.lmm offset).
The polarization state of the laser beam is unaltered. The prisms are coated to minimize reflection losses. Beam deviation may be altered by up to one degree, typically less. The output side of the housing is counterbored to accommodate interchangeable diode laser objectives in mounted cells (not included).
Input beam diameter can be up to 8 x 4mm. Outer black-anodized aluminum housing diameter is 30.15mm. Length is 38.1mm. Wavefront error held to less than � wave at 830nm.
The prism system is in superb condition both optically and cosmetically. The set screw for retaining the optional objective is absent.
***MPN GPA-2X-8.0-830
***OEM Melles Griot
***SKU*** 23146
-
$50.00
ISP Optics GE-W-25-2 Germanium Infrared Window
Diameter: 25mm
Thisckness: 2mm
Specifications:
– Dia tolerance: +0, -0.005″(+0, -0.13mm)
– Th tolerance: �0.005� (�0.13mm)
– Clear Aperture: 85%
– Parallelism: 3 arc min
– Flatness: 1/10 wave at 10.6 um
– Surface Finish: 40/20
***MPN GE-W-25-2
***OEM ISP Optics
***SKU*** 28028
-
$50.00
This is a plano-cylindrical lens. These lenses have a defined magnification in one direction, and perpendicular to that direction they are effectively ‘unpowered’. Cylindrical lenses find numerous applications in holography, as well as imaging elongated slits in spectrometers and monochromators.
Characteristics of this lens include:
� Focal length – Positive 100mm
� Length – 40mm
� Width – 25mm
� Manufacturer – Unknown
� Part number – Unknown
� Glass type – BK7 ?
� Uncoated
� Condition – no visible defects
Please note – unless we are able to determine that a lens is a higher precision type (either by part number or by nomenclature on the lens itself) then it should be assumed that the lens has a low precision figure. When we have determined that a lens is definitely a low precision grade, then that will be stated in the lens characteristics.
Photo set 1474
***MPN
***OEM Custom
***SKU*** 21503
-
$55.00
This is a plano-cylindrical lens. These lenses have a defined magnification in one direction, and perpendicular to that direction they are effectively ‘unpowered’. Cylindrical lenses find numerous applications in holography, as well as imaging elongated slits in spectrometers and monochromators.
Characteristics of this lens include:
� Focal length – Positive 100mm
� Length – 60mm
� Width – 50mm
� Manufacturer – Melles Griot
� Part number – 01-LCP-011
� Glass type – BK7
� Uncoated
� Condition – no visible defects
Please note – unless we are able to determine that a lens is a higher precision type (either by part number or by nomenclature on the lens itself) then it should be assumed that the lens has a low precision figure. When we have determined that a lens is definitely a low precision grade, then that will be stated in the lens characteristics.
Photo set 1473
***MPN 01-LCP-011
***OEM Melles Griot
***SKU*** 21502
-
$55.00
This is a plano-cylindrical lens. These lenses have a defined magnification in one direction, and perpendicular to that direction they are effectively ‘unpowered’. Cylindrical lenses find numerous applications in holography, as well as imaging elongated slits in spectrometers and monochromators.
Characteristics of this lens include:
� Focal length – Positive 100mm
� Length – 32mm (cut down?)
� Width – 50mm
� Manufacturer – Unknown
� Part number – 8100-32
� Glass type – BK7 ?
� Uncoated
� Condition – no visible defects
Please note – unless we are able to determine that a lens is a higher precision type (either by part number or by nomenclature on the lens itself) then it should be assumed that the lens has a low precision figure. When we have determined that a lens is definitely a low precision grade, then that will be stated in the lens characteristics.
This lens includes a lens mount that is 2 inches wide and 15/16 inches tall. The support shelf sits 1/2 inch above the base. The width of the aperture formed by the support arms is 1 3/8 inches. The bottom portion of the lens has been masked by black tape, easily removed if desired.
Photo set 1471
***MPN 8100-32
***OEM Custom
***SKU*** 21500