Showing all 9 resultsSorted by latest
-
-
Analog Devices ADL 5521 Low Noise Amplifier
$120.00The ADL5521 is a high performance GaAs pHEMT low noise
amplifier. It provides high gain and low noise figure for single-
downconversion IF sampling receiver architectures as well as
direct-downconversion receivers.
The ADL5521 provides a high level of integration by incorporating
the active bias and dc blocking capacitors, making it very easy
to use while not sacrificing design flexibility.The ADL5521 is easy to tune, requiring only a few external
components. The device can support operation from 3 V to 5 V,
and the current draw can be adjusted with the external bias
resistor for applications requiring low power consumption.
The ADL5521 comes in a compact, thermally enhanced, 3 mm ×
3 mm LFCSP and operates over the temperature range of
−40°C to +85C. -
Analog Devices Evaluation Board ADMT717x
$45.00Analog Devices ADM717x-EVALZ Evaluation Boards help designers evaluate the capabilities of the ADM7170/ADM7171/ADM7172 Ultra-low Noise, High PSRR, Fast Transient Response CMOS Low Dropout Linear Regulators (LDO). Operating from 2.3V to 6.5V and delivering up to 500mA of output current, the ADM7170/ADM7171/ADM7172 LDOs are ideal for the regulation of high-performance analog and mixed-signal circuits operating from 6V down to 1.2V rails. Using the ADM7170ACP-EVALZ/ADM717Q1CP-EVALZ/ ADM7172ACP-EVALZ evaluation boards, designers can access simple device measurements including line and load regulation, dropout, and ground current with a single voltage source, a voltmeter, an ammeter, and load resistors. -
-
Analog Devices Evaluation Board ADL5801
$100.00Analog devices ADL5801-EVAZ technical specifications, attributes, and parameters.
Evaluation Board For High IP3, 10 MHz to 6GHz, Active Mixer.
ADL5801 Up-Down Converter and Mixer Evaluation Board..
EVALUATION BOARD, WIDEBAND ACTIVE MIXER:
TECHNICAL
Evaluation Kit yes
Frequency 10MHz
Noise Figure 9.5dB
Nominal Supply current 130mA
Operating Supply Current 130mA
Operating Supply Voltage 5.25V
P1dB 13.3dB
COMPLIANCE
Lead Free Contains Lead
REACH SVHC No SVHC
-
-
Zynq Xilinx by Whizz systems LSI Controller Card SV00504358
$900.00Zynq Xilinx by Whizz systems LSI Controller Card SV00504358
product is untested.
It is the buyers responsibility to verify compatibility prior to purchase.
-
HP Ethernet 1Gb-port 331 FLR Adapter Card
$80.00PLEASE CHECK THE COMPATIBILITY OF THIS NETWORK CARD WITH YOUR CURRENT HARDWARE. it IS THE BUYERS RESPONSIBILITY TO VERIFY THE COMPATIBILITY PRIOR TO PURCHASE.
GOOD CONDITION. PULLED FROM THE ORIGINAL MACHINE AND VISUALLY INSPECTED FOR DEFECTS.
THE BUYER IS RESPONSIBLE FOR PAYMENT OF ANY DUTIES, TARIFFS, OR TAXES DUE UPON RECEIPT OF THIS ITEM.
ONLY WHAT IS IN THE PHOTO IS INCLUDED IN THE SALE. IF A PART IS NOT SHOWN IN HTE PHOTOS, THEN IT IS NOT INCLUDED IN THE SALE OF THIS ITEM.
-
Gumstix Overo and Tobiwo 27950 GS3503T-R2889
$150.00Gumstix Overo and Tobiwo 27950 GS3503T-R2889
The typical Gumstix configuration consists of a computer-on-module or COM and an expansion board.
- The expansion board can be off-the-shelf from Gumstix or custom made. Gumstix openly publishes the schematics of all off-the-shelf expansion boards to assist rapid development of custom solutions.
- For some applications, a camera board can be connected to the top of the Overo COM via a ribbon cable.
- A typical Verdex Pro assembly consists of a Verdex Pro COM sandwiched between a 60-pin expansion board and an 80-pin expansion board.
The DuoVero COM, Overo COM and Verdex Pro COMs are unique to Gumstix.
The following information addresses the most common expansion options: a DuoVero COM with Parlor expansion board, an Overo COM mounted on a Tobi expansion board, and a Verdex Pro COM mounted on a Console-VX expansion board.
Overo and Tobi
Gumstix Overo 
Gumstix Tobi An Overo COM connects to an Overo series expansion board via the two 70-pin AVX connectors located on the bottom side of the COM. Place the Tobi board on a flat, static-safe surface, align the COM with the white outline on the board above the connectors and gently press on the COM until it clicks into place.
